[App_rpt-users] Alternate IAX port >> Registered ok but not listed?

Jon Rorke jrorke at cogeco.ca
Wed Oct 10 10:01:58 EDT 2012


You need to change the bindport=4570 in the IAX.conf file if you want to 
use something other than 4569. Then forward the ports in the router.

You may need to reboot your server for it to take affect.

Jon VA3RQ
On 10/9/2012 8:29 PM, Kevin Oleniczak wrote:
> I had already done that in the portal but it still wasn't working. As 
> an experiment, i changed everything back to the original 4569 port and 
> forwarded that on my router. I could then connect with the 
> webtransceiver. However i can't leave it there and need to get it to 
> work on an alternate port. It seems from my testing that something is 
> hard set to port 4569 on the allstar end of things?
>
> ideas?
>
> thank you
>
> On Tue, Oct 9, 2012 at 3:47 AM, Ken <ke2n at cs.com <mailto:ke2n at cs.com>> 
> wrote:
>
>     Yes -- you need to log onto the portal and get to the server
>     configuration tab -- there is a place there to change to port
>     number that the registration server is talking to.
>
>     Ken
>
>     *From:*app_rpt-users-bounces at ohnosec.org
>     <mailto:app_rpt-users-bounces at ohnosec.org>
>     [mailto:app_rpt-users-bounces at ohnosec.org
>     <mailto:app_rpt-users-bounces at ohnosec.org>] *On Behalf Of *Kevin
>     Oleniczak
>     *Sent:* Tuesday, October 09, 2012 12:09 AM
>     *To:* app_rpt-users at ohnosec.org <mailto:app_rpt-users at ohnosec.org>
>     *Subject:* [App_rpt-users] Alternate IAX port >> Registered ok but
>     not listed?
>
>     I am unable to connect to my node from the webtransceiver and
>     don't see it listed on the active nodes page. I use an alternate
>     iax port because i have to.
>
>     From reading other posts... it seems I may need an admin to change
>     my iax port from 4569 to what I now want to use which is 4570?
>     thoughts?
>
>     My registration is still showing 4569 and am forwarding 4570 on my
>     router to my ACID box.
>
>     cruiser*CLI> iax2 show registry
>
>     Host dnsmgr  Username    Perceived Refresh  State
>
>     <myip>:4569 N       28970       <myip>:4569 60  Registered
>
>     I'm not seeing my node show up and believe this is the cause. In
>     my iax.conf I have bindport set 4570 and also in server config
>     under network I set port 4570 on the portal.
>
>     looking at rpt_extnodes i see my node listed with the correct port...
>
>     28970=radio@<myip>:4570/28970,<myip>
>
>     [general]
>
>     bindaddr=0.0.0.0
>
>     bindport=4570
>
>     ....
>
>     register=28970:<mypasswd>@register.allstarlink.org
>     <http://register.allstarlink.org>
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20121010/195e459e/attachment.html>


More information about the App_rpt-users mailing list