[App_rpt-users] Alternate IAX port >> bind port not working

Jon Rorke jrorke at cogeco.ca
Fri Oct 12 08:07:40 EDT 2012


I check the node I am working on and it has the following:

> ; Inter-Asterisk eXchange driver definition
> ;
> ;
>
> [general]
> bindport=4570
> bindaddr=0.0.0.0
> disallow=all
> allow=gsm
> allow=g726aal2
> allow=ulaw
> jitterbuffer=yes
> forcejitterbuffer=yes
> dropcount=2
> maxjitterbuffer=4000
> maxjitterinterps=10
> resyncthreshold=1000
> maxexcessbuffer=80
> minexcessbuffer=10
> jittershrinkrate=1
> tos=0x1E
> autokill=yes
> delayreject=yes
> ;iaxthreadcount=30
> ;iaxmaxthreadcount=150

So bindport is set correctly but the node is still reporting to all the 
others as port 4569. in the RPT_extnodes list.

28505=radio at 66.206.229.10:4569/28505,66.206.229.10
I have port 4570 open in the router but the node is not reachable 
because of this.


On 10/12/2012 12:12 AM, Kevin Oleniczak wrote:
> I finally got this working. To close this out, here's what i found.
>
> It turns out the issue was that i had binaddr listed above bindport in 
> iax.conf. In order for bindport to get used, it has to appear in the 
> file before bindaddr.
>
> thanks to all who helped with this.
>
> On Tue, Oct 9, 2012 at 8:40 PM, Tim Sawyer <tim.sawyer at mac.com 
> <mailto:tim.sawyer at mac.com>> wrote:
>
>     Try changing your IP address setting on the Portal to either DHCP
>     or Fixed. I don't know what the VoIP setting you currently have it
>     set for does.
>     --
>     Tim
>     :wq
>
>     On Oct 9, 2012, at 5:29 PM, Kevin Oleniczak
>     <kevinoleniczak at gmail.com <mailto:kevinoleniczak at gmail.com>> wrote:
>
>>     I had already done that in the portal but it still wasn't
>>     working. As an experiment, i changed everything back to the
>>     original 4569 port and forwarded that on my router. I could then
>>     connect with the webtransceiver. However i can't leave it there
>>     and need to get it to work on an alternate port. It seems from my
>>     testing that something is hard set to port 4569 on the allstar
>>     end of things?
>>
>>     ideas?
>>
>>     thank you
>>
>>     On Tue, Oct 9, 2012 at 3:47 AM, Ken <ke2n at cs.com
>>     <mailto:ke2n at cs.com>> wrote:
>>
>>         Yes -- you need to log onto the portal and get to the server
>>         configuration tab -- there is a place there to change to port
>>         number that the registration server is talking to.
>>
>>         Ken
>>
>>         *From:*app_rpt-users-bounces at ohnosec.org
>>         <mailto:app_rpt-users-bounces at ohnosec.org>
>>         [mailto:app_rpt-users-bounces at ohnosec.org
>>         <mailto:app_rpt-users-bounces at ohnosec.org>] *On Behalf Of
>>         *Kevin Oleniczak
>>         *Sent:* Tuesday, October 09, 2012 12:09 AM
>>         *To:* app_rpt-users at ohnosec.org
>>         <mailto:app_rpt-users at ohnosec.org>
>>         *Subject:* [App_rpt-users] Alternate IAX port >> Registered
>>         ok but not listed?
>>
>>         I am unable to connect to my node from the webtransceiver and
>>         don't see it listed on the active nodes page. I use an
>>         alternate iax port because i have to.
>>
>>         From reading other posts... it seems I may need an admin to
>>         change my iax port from 4569 to what I now want to use which
>>         is 4570? thoughts?
>>
>>         My registration is still showing 4569 and am forwarding 4570
>>         on my router to my ACID box.
>>
>>         cruiser*CLI> iax2 show registry
>>
>>         Host dnsmgr  Username Perceived             Refresh  State
>>
>>         <myip>:4569 N       28970 <myip>:4569          60 Registered
>>
>>         I'm not seeing my node show up and believe this is the cause.
>>         In my iax.conf I have bindport set 4570 and also in server
>>         config under network I set port 4570 on the portal.
>>
>>         looking at rpt_extnodes i see my node listed with the correct
>>         port...
>>
>>         28970=radio@<myip>:4570/28970,<myip>
>>
>>         [general]
>>
>>         bindaddr=0.0.0.0
>>
>>         bindport=4570
>>
>>         ....
>>
>>         register=28970:<mypasswd>@register.allstarlink.org
>>         <http://register.allstarlink.org/>
>>
>>
>>     _______________________________________________
>>     App_rpt-users mailing list
>>     App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>>     http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20121012/b590b6f0/attachment.html>


More information about the App_rpt-users mailing list