[App_rpt-users] G707 Remote Base Locking Up on URI

Monty monty at ke7jvx.com
Sat Jun 22 19:35:14 EDT 2013


Any ideas Jim?

Monty
On Jun 14, 2013 7:30 AM, "Jeff Carrier" <k0jsc.jeff at gmail.com> wrote:

> Mine too, exact same situation.  I have to drop the power supply on the G7
> to reset it.  That's not conducive to "mountain top" operation so it's
> still on the bench.
>
> K0JSC
>
> On Wed, Jun 12, 2013 at 12:36 PM, Kirk <wb6egr at gmail.com> wrote:
>
>>  Thats not whats occuring with mine, the radio actually goes dark or
>> stops answering the controller. Sometimes it will continue to TX/RX on the
>> last frequency....  *2 *3 makes no differance
>>
>> Sent from my piece of Crap I-Phone... I feel a Samsung 4 is in my near
>> future
>>
>>
>> On Jun 12, 2013, at 7:44 AM, "Scott Weis" <kb2ear at kb2ear.net> wrote:
>>
>>   Try this, as it has been working for me for a while.  ****
>>
>> ** **
>>
>> Instead of connecting to the remote base with a *3 connect with a *2.
>> You should be able to control the radio until the cows come home. Then do a
>> *3 to talk on the specific channel.  I have found that as soon as the radio
>> TXs I am unable to control it any more.****
>>
>> ** **
>>
>> Also I find the once I can’t control the G707 any more I do a *1 and
>> disconnect then a *2 again and all is well again.****
>>
>> ** **
>>
>> I’ve been meaning to talk to Jim about this bug..  ****
>>
>> ** **
>>
>> Scott****
>>
>> ** **
>>
>> *From:* app_rpt-users-bounces at ohnosec.org [mailto:
>> app_rpt-users-bounces at ohnosec.org] *On Behalf Of *Jeff Carrier
>> *Sent:* Wednesday, June 12, 2013 1:15 AM
>> *To:* Monty
>> *Cc:* app_rpt mailing list; K&R Yoksh
>> *Subject:* Re: [App_rpt-users] G707 Remote Base Locking Up on URI****
>>
>> ** **
>>
>> I have the same issue.  First with a home brew interface so I searched hi
>> and low for the "actual" interface board with the same issue as Kirk
>> describes.****
>>
>> De k0jsc****
>>
>> On Jun 11, 2013 9:41 PM, "Monty" <monty at ke7jvx.com> wrote:****
>>
>> Hi Kyle,****
>>
>> ** **
>>
>> I fixed the syntax error, still no joy.  I did have a usbradio node and
>> the 707 on simpleusb, so I migrated the 707 to usbradio and removed all the
>> simpleusb configs, still no joy.  Any other ideas?
>> ****
>>
>>
>> Monty****
>>
>> ** **
>>
>> On Tue, Jun 11, 2013 at 6:42 PM, K&R Yoksh <yokshs at gmail.com> wrote:****
>>
>> Hello Monty,
>> While not specific to the remote operation, I see one thing that might
>> make app_rpt lose it's mind.
>>
>> The rxchannel parameter is very picky about syntax, especially the upper
>> and lower case letters. The correct format is:
>>
>> rxchannel=SimpleUSB/usb1010
>>
>> Another thing I've learned is to never (NEVER) have usbradio.conf and
>> simpleusb.conf exist in /etc/asterisk at the same time. This will
>> confuse app_rpt at the least, or crash it altogether.
>>
>> 73,
>>
>> Kyle Yoksh
>> K0KN
>> Olathe, KS
>> Allstar 2210-2219
>> --- Original Message ---Hello Everyone,****
>>
>>
>>
>> I have tried two Kenwood G707s with three of Jim's URI Adapter cards and
>> two URIs on two different computers.  I am able to get three or four
>> commands (freq, pl tone, etc) then I will get Allison saying "Invalid
>> Frequency" and the CLI shows:
>>
>> "WARNING[7925]: app_rpt.c:13876 serial_remote_io: -99999 Serial device not
>> responding on node 1010"
>>
>> The radio will not steer or accept commands anymore until I power cycle
>> the
>> 707.  The after power cycle three or four commands and will not steer
>> again.  I have tried the same computer with a VHF Syntor with an xcat and
>> will accept every command without issue.  Also one of my 707s now lives on
>> a Quad PCI card and steers with every command without issue.  Has anyone
>> else seen this or know the remedy?  Below is my rpt.conf with the URI:
>>
>> [1010]
>> archivedir=/etc/asterisk/qso
>> rxchannel = simpleusb/usb1010
>> duplex=0
>> ioport = /dev/ttyS0
>> remote = kenwood
>> authlevel = 1
>> memory=memory
>> remote_inact_timeout=5400
>> remote_timeout=5400
>> functions=remote-functions
>> phone_functions=remote-functions
>> link_functions=remote-functions ****
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users****
>>
>> ** **
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users****
>>
>>  _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20130622/1bf0c7b0/attachment.html>


More information about the App_rpt-users mailing list