[App_rpt-users] GM300

Kirk Just Kirk wb6egr at gmail.com
Fri May 10 17:49:48 EDT 2013


Be nice! One remote still has a tall green can in it (Automatic Electric)
DIAL 4 for UHF please.......


On Fri, May 10, 2013 at 11:44 AM, Bryan D. Boyle <bdboyle at bdboyle.com>wrote:

> or even electromechanical...:)   Strowger switches arestill useful
> devices, even if outdated...;)
>
> --
> Bryan
> Sent from my iPhone 5...small
> keyboard, big fingers...please
> forgive misspellings...
>
>
>
> On May 10, 2013, at 17:31, Jim Duuuude <telesistant at hotmail.com> wrote:
>
> Just a suggestion in general:
>
> We are ham radio operators. By definition, we have, at least, a certain
> basic knowledge of
> electronics (as is required to pass our test).
>
> If two devices are somehow electrically incompatible with each other, use
> your knowledge of
> electronics to build a simple circuit to interface them together.
> Converting from one set of
> "levels" to another is REALLY not that difficult.
>
> That's why we are what we are, and do what we do.
>
> Jim WB6NIL
>
> P.S. Or, you can use pin 8  *LIKE EVERY ONE ELSE DOES*!!
>
>
>
> > From: n5zua at earthlink.net
> > To: app_rpt-users at ohnosec.org
> > Date: Fri, 10 May 2013 16:14:00 -0500
> > Subject: Re: [App_rpt-users] GM300
> >
> > <http://www.batlabs.com/images/gmacc8.gif>
> >
> > Gotcha. Not sure if you mentioned if yours was a 16 channel or not. If
> an 8
> > channel, the above link lists pin 4 as a spare, and instructs that pin 8
> > should be used for COR active low. Since you mentioned getting voltage
> out
> > of pin 4, I'm assuming yours is a 16 channel radio. Folks with an 8
> channel
> > model would not have the option you are using.
> >
> > N5ZUA
> >
> > ----- Original Message -----
> > From: "Bill Hurlock" <bill.hurlock at cpcomms.com>
> > To: <app_rpt-users at ohnosec.org>
> > Sent: Friday, May 10, 2013 3:54 PM
> > Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 51, Issue 9
> >
> >
> > > Here is a clip about PIN 4 in the Accessory plug of a GM300.
> > >
> > > 4 Programmable Output Only This is a radio output port. It is an open
> > > collector output which saturates to A+ supply when active. It is
> normally
> > > used to drive an external relay or sense lead. It duplicates the
> function
> > > of J3-3 of the five pin logic board. When active it can source a
> maximum
> > > current of 250 mA.
> > > The pin has a 10 K ohm resistor pull-down to ground on the logic
> board.
> > > and uses a PNP transistor to switch it up to 12V. This pin does not
> work
> > > as an active low pin (i.e. pulling something to ground), only as an
> active
> > > high (that is dragging something up to +12v). If you want an active
> high
> > > output to drive a reed relay which has the other side of the coil to
> > > ground, this is your pin (but don't forget to check that the backwards
> > > diode is present on the coil pins).
> > >
> > > Bill Hurlock
> >
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20130510/42e212a1/attachment.html>


More information about the App_rpt-users mailing list