[App_rpt-users] I/O using parallel port

Jamey Wright jamey.wright at charter.net
Sun Aug 9 18:47:19 EDT 2015


I searched all through the rpt.conf file and could not find any duplicates.
These are the only functions I have added.  Everything else is what comes in
the file by default.   For good measure I changed the commands to 3 digit
commands starting right after the 900 series commands.  Still does not work.


At a loss

Jamey
WR4JW

-----Original Message-----
From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of mike at midnighteng.com
Sent: Saturday, August 08, 2015 6:41 PM
Cc: app_rpt-users at ohnosec.org
Subject: Re: [App_rpt-users] I/O using parallel port


The problem from what you are describing is not with the PP at all.
It is your command structure.
You must have a conflicting command start.

Scrub though your command list and look for assignments that start with:

two digit -84 and/or
three digit -840/841 etc.

Asterisk always runs with the first match.
If the is a 2 digit command 84, anything else starting with 84 will never
execute. (It will always execute 84 command not 84x, 84xx, 84xxx, 84xxxx) .

I often warn everyone to organize their command list in numeric order so you
don't do such a thing.

If you find one, you can convert it to a non-conflicting 4 digit command and
you are fine. (8400)

...mike/kb8jnm


>
>
> -----Original Message-----
> From: mike at midnighteng.com [mailto:mike at midnighteng.com]
> Sent: Saturday, August 08, 2015 12:36 PM
> To: Jamey Wright app_rpt-users at ohnosec.org <jamey.wright at charter.net>
> Subject: RE: [App_rpt-users] I/O using parallel port
>
>
>>> 8401=cop,61,pp2=0
>>> 8411=cop,61,pp2=1
>
> The commands you created in rpt.conf is the definition.
> Use them directly or in a macro for complex function.
>
> Read online manual
> http://ohnosec.org/drupal/node/177
>
> ...mike/kb8jnm
>
> I have read the manual... and every website I can find dealing with 
> this and I cannot make it work.  I don't know what I am missing but 
> there is something.  Just for a sanity check, I built a LED circuit 
> and connected it to the parallel port.  If I set it to "pp2 = out0" in 
> simpleusb.conf the LED is not lit.  If I change it to "pp2 = out1" the 
> LED is lit so I know the port is working.  For whatever reason, I 
> cannot control those pins from DTMF or sent from IAXRPT.
>
> This is from rpt.conf:
>
> [functions27981]
>
> <snip>
>
> 8401 = cop,61,pp2=0
> 8402 = cop,61,pp3=0
> 8403 = cop,61,pp4=0
> 8404 = cop,61,pp5=0
> 8405 = cop,61,pp6=0
> 8406 = cop,61,pp7=0
> 8407 = cop,61,pp8=0
> 8408 = cop,61,pp9=0
>
> 8411 = cop,61,pp2=1
> 8412 = cop,61,pp3=1
> 8413 = cop,61,pp4=1
> 8484 = cop,61,pp5=1
> 8415 = cop,61,pp6=1
> 8416 = cop,61,pp7=1
> 8417 = cop,61,pp8=1
> 8418 = cop,61,pp9=1
>
> Maybe I am misunderstanding the way to setup and use the commands.  My 
> understanding is that I should be able to just dial *8411 and set pp2 
> to 1?
>
> Thanks
>
> Jamey
> WR4JW
>
>


_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem. 




More information about the App_rpt-users mailing list