[App_rpt-users] Correct Wiring For The URIx Diagnostic Dongle

John C. Westmoreland, P.E. john at westmorelandengineering.com
Fri Aug 14 05:53:28 EDT 2015


Bob,

Yes - point is here - if you follow the wiring diagram in the OP - it can't
work - it doesn't have power unless you connect up the 9095 test fixture.
(Pin 24).

73's,
John
AJ6BC


On Fri, Aug 14, 2015 at 2:10 AM, kk6ecm <kk6ecm at gmail.com> wrote:

> That is the 6dB amplifier talked about in
> http://www.dmkeng.com/images/URIx%20Data%20Sheet.pdf
>
> Thanks,
> Bob
> kk6ecm
>
> Sent from iPad
>
>
> On Aug 13, 2015, at 10:51 PM, John C. Westmoreland, P.E. <
> john at westmorelandengineering.com> wrote:
>
> Hello Again,
>
> To get correct results - doesn't it make more sense to wire up this:
> http://www.dmkeng.com/images/URIx_TEST_FIXTURE.pdf
>
> From the above - how does AIN (pin 24) work?
>
> 73's,
> John
> AJ6BC
>
>
> On Wed, Aug 12, 2015 at 10:39 PM, John C. Westmoreland, P.E. <
> john at westmorelandengineering.com> wrote:
>
>> Hello All,
>>
>> Here is the wiring instructions from the FAQ:
>>
>> Pin 1 to Pin 7
>> Pin 2 to Pin 3
>> Pin 4 to Pin 8
>> *Pin 23 to Pin 24*
>> 10K Resistor between Pins 21 and 22
>> 10K Resistor between Pins 21 and *23*
>> For URIx (CM119) only, also include the following connections:
>> Pin 5 to Pin 10
>> Pin 6 to Pin 11
>>
>> From uridiag:
>>
>> Enter your selection:c
>> Special Test Cable Pinout:
>>
>> 25 pin D-shell connector
>>   Pin 1 to Pin 7
>>   Pin 2 to Pin 3
>>   Pin 4 to Pin 8
>>  * Pin 11 to Pin 24*
>>   10K Resistor between Pins 21 & 22
>>   10K Resistor between Pins 21 & 23
>>   For URIx (CM119), also include the following:
>>   Pin 5 to Pin 10
>>   Pin 6 to Pin* 11*
>>   Do *NOT* include these for the standard URI!!
>>
>> So, which one of these do I use?
>>
>> 73's,
>> John
>> AJ6BC
>>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20150814/d034d6d2/attachment.html>


More information about the App_rpt-users mailing list