[App_rpt-users] Need help connecting a Baofeng UV-5R with DMK URI-x

Shamim Shahriar shamim.shahriar at gmail.com
Tue Nov 3 08:43:41 EST 2015


Hello all

Further to my previous email, i have come across this link

http://latinovoip.net/baofeng-uv-6-as-an-irlpecholinkallstarlink-2-meter-or-440-mhz-70cm-radio/

This one is using a UV-6R, but i am assuming that the pinout for speaker
mic is the same.

Would appreciate if someone could please confirm.

Thanks and regards
Shamim
On 3 Nov 2015 13:37, "Steven Donegan" <donegan at donegan.org> wrote:

> I am also looking to connect a UV-5R to the URI-X but using ONLY the
> speaker/mike jack and usbradio with DSP detection of audio - the radio will
> do the CTCSS handling and should only provide audio when CTCSS is met.
>
> Thanks!
>
> Steven Donegan
> KK6IVC General Class FCC License
> Silver State Car #86
> www.sscc.us
>
> ------------------------------
> *From:* Shamim Shahriar <shamim.shahriar at gmail.com>
> *To:* app_rpt-users at ohnosec.org
> *Sent:* Monday, November 2, 2015 4:45 PM
> *Subject:* [App_rpt-users] Need help connecting a Baofeng UV-5R with DMK
> URI-x
>
> Dear List members
>
> Good morning. I need a bit of help in connecting a Baofeng UV-5R with
> DMK URIx device. I have googled as much as I practically could, but
> still could not decide/confirm as to what should be the approach.
>
> First of all, I came across the pin-out for the baofeng at Miklor site
> http://www.miklor.com/COM/UV_Technical.php
> I have also seen how DMK suggests any generic radio should be connected
> at http://www.dmkeng.com/images/9080-FRS.pdf
>
> And finally, I have found the site that shows how to get the COR out of
> baofeng http://alaskareflector.org/zl1nc/UV-COS.html
>
> Now, my expertise in electronics is sub-zero -- I know some very basics
> about what component does what, and that's all. So, I have several
> questions, and would appreciate if someone with sufficient relevant
> experience could please point me to the correct decision.
>
> 1. the URI diagram uses several resistors, do I really need them? Or
> should I just connect things direct?
> 2. the main URI diagram shows pin 7 as CTCSS_det and pin 8 as COR_det,
> so should I connect the COR from baofeng to pin 8?
> 3. based on what I can understand from all the links above, I should
> connect
>
> large stereo body -> D-Sub pin 1
> large stereo ring -> D-Sub pin 22
> small stereo tip -> D-Sub pin 21
> COR (taken from pin 2 of the IC) -> D-Sub pin 8
>
> Is the above correct? Or do you have different experience?
>
> Thanks for your response.
>
> Regards
> Shamim
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> and scroll down to the bottom of the page. Enter your email address and
> press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20151103/9bf17e81/attachment.html>


More information about the App_rpt-users mailing list