[App_rpt-users] Shared repeater tone panel

Steve Mahler kizzy at lusfiber.net
Fri Jul 22 13:10:04 EDT 2016


Joe:

I've done this, it is working great in testing.  Here are the parts ...

1) APP_RPT doesn't support all PL tones (ACID Distribution) ... I 
believe that this is the valid decode list (any PL can be transmitted) ...

PL 	NOTES
	
67.0 	
69.3 	Not Available in AllStar RX DSP
69.4 	Not Available in AllStar RX DSP
71.9 	
74.4 	
77.0 	
79.7 	
82.5 	
85.4 	
88.5 	
91.5 	
94.8 	
97.4 	
100.0 	
103.5 	
107.2 	
110.9 	
114.8 	
118.8 	DO NOT USE - 60 Hz Harmonic
123.0 	
127.3 	
131.8 	DO NOT USE - DCS Turn Off Code
136.5 	DO NOT USE - DCS Turn Off Code
141.3 	
146.2 	
151.4 	
156.7 	
159.8 	Not Available in AllStar RX DSP
162.2 	
165.5 	Not Available in AllStar RX DSP
167.9 	
171.3 	Not Available in AllStar RX DSP
173.8 	
177.3 	Not Available in AllStar RX DSP
179.9 	DO NOT USE - 60 Hz harmonic
183.5 	Not Available in AllStar RX DSP
186.2 	
189.9 	Not Available in AllStar RX DSP
192.8 	
196.6 	Not Available in AllStar RX DSP
199.5 	Not Available in AllStar RX DSP
203.5 	
206.5 	Not Available in AllStar RX DSP
210.7 	
218.1 	
225.7 	
229.1 	Not Available in AllStar RX DSP
233.6 	
241.8 	
250.3 	
254.1 	Not Available in AllStar RX DSP

	

2) The method to associate RX and TX tones and have valid decode of 
certain PLs  in usbradio.conf  is ....

;
; CTCSS / PL TONES
txctcssdefault= 103.5   ; default tx ctcss freq, any frequency 
permitted, used when RX is quiet

rxctcssfreqs= 67.0,88.5,103.5,136.5,192.8,250.3
                         ; rx ctcss freqs in floating point. must be in 
table

txctcssfreqs= 67.0,88.5,103.5,103.5,192.8,250.3
                         ; tx ctcss freqs, any frequency permitted

;
; RECEIVER CONTROLS
;
rxctcssoverride=0       ; Set to 1 or yes to start out in carrier 
squelch mode

rxctcssrelax=0          ; reduce talkoff from radios w/o CTCSS Tx HPF
;                       ; (help radios with DTMF Twist)

** Note, you can cross PLs ... when the above receives 136.5 it 
transmits 103.5

Like I said, so far it has all worked ... just feed voice and PL from 
the discriminator to the AllStar server.  Good Luck!

...STeve - KF5VH



On 7/22/2016 10:29 AM, Joe Moskalski wrote:
> I have a need to setup a community repeater. This is done easily with 
> a shared repeater tone panel and the like from CSI. I was wondering if 
> this could be accomplished using app_rpt. All it would need to do is 
> allow the use of multiple input and output PL tones. Simply put, when 
> the repeater receives X pl tone it transmits the X pl tone on the 
> output and when the repeater receives Y pl tone it transmits the Y pl 
> tone on the output.
> If anyone has done this or has any idea on how this would be 
> accomplished it would be much appreciated.
> Thanks in advance!
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20160722/c98e79f2/attachment.html>


More information about the App_rpt-users mailing list