[App_rpt-users] I forgot how to setup Callcentric again..

Mark Johnston markjohnston73 at gmail.com
Sat Nov 5 21:08:01 EDT 2016


*In /etc/modules.conf is sip loaded?*

*load => chan_sip.so ;                           Session Initiation
Protocol (SIP)*



*Check against what I am using below, another issue I have run into is
sometimes after boot I have to run*

*asterisk -rx "sip reload" to get it to connect/work... *


*Hope this helps...*


*SIP.conf:*

*; SIP Configuration example for Asterisk*

*;*

*[general]*

*context = default*

*                                ; Default context for incoming calls*

*allowoverlap = no               ; Disable overlap dialing support.
(Default is yes)*

*bindport = 5060                 ; UDP Port to bind to (SIP standard port
is 5060)*

*bindaddr = 0.0.0.0              ; IP address to bind to (0.0.0.0 binds to
all)*

*srvlookup = yes                 ; Enable DNS SRV lookups on outbound calls*

*                                ; Note: Asterisk only uses the first host*

*                                ; in SRV records*

*                                ; Disabling DNS SRV lookups disables the*

*                                ; ability to place SIP calls based on
domain*

*                                ; names to some other SIP users on the
Internet*


*dtmfmode = rfc2833*

*context=from-callcentric*

*srvlookup=yes*

*register => 1777:YOURPASSWORDHERE at callcentric.com
<1777%3AYOURPASSWORDHERE at callcentric.com>*

*session-timers=refuse*


*[callcentric]*

*type=peer*

*context=from-callcentric*

*host=callcentric.com <http://callcentric.com>*

*fromdomain=callcentric.com <http://callcentric.com>*

*username=1777........*

*fromuser=1777........*

*secret=YOURPASSWORDHERE*

*insecure=port,invite*

*canreinvite=no*

*disallow=all*

*allow=ulaw*



*[100] ;this is your extension # at call centric. usually 100-150*

*context=to-callcentric*

*type=friend*

*defaultuser=1777.......*

*secret=YOURPASSWORDHERE*

*host=dynamic*


Extensions.conf:


*[to-callcentric]*

*exten => _X.,1,Dial(SIP/${EXTEN}@callcentric)*


*RPT.conf:*

*6=autopatchup,context=to-callcentric,noct=1,farenddisconnect=1,dialtime=20000*

"Got Root?"

How many software engineers does it take to change a light bulb?
*None. It's a hardware problem.*


Unix is user friendly. It's just very particular about who it's friends are.
WINDOWS: Will Install Needless Data On Whole System
MICROSOFT: Most Intelligent Customers Realize Our Software Only Fools
Teenagers.


A ntennas
P oorly
P laced
L acks
E ngineering

The best way to accelerate a computer running Windows is at 9.81 m/s².

*"I get paid to support Windows, I use Linux to get work done."*


On Sat, Nov 5, 2016 at 2:41 PM, Loren Tedford <lorentedford at gmail.com>
wrote:

> Here is the information i have so far.. For some reason i just can't make
> out going calls it seems to register with callcentric ok kinda confused as
> to where i might have mixed this up..
>
> http://forum.kc9zhv.com/index.php/topic,22.0.html
>
>
> So.. Here is the errors i get when i try to make a call from my hand
> held..
> [Nov  5 16:19:37] WARNING[2489]: chan_sip.c:2946 create_addr: No such
> host: callcentric
> [Nov  5 16:19:37] WARNING[2489]: chan_sip.c:2946 create_addr: No such
> host: callcentric
> [Nov  5 16:19:37] WARNING[2489]: app_dial.c:1242 dial_exec_full: Unable to
> create channel of type 'SIP' (cause 20 - Unknown)
> [Nov  5 16:19:37] WARNING[2489]: app_dial.c:1242 dial_exec_full: Unable to
> create channel of type 'SIP' (cause 20 - Unknown)
> rpt*CLI>
>
> Does my forum look correct? with out the username and password listed but
> still confused as to what i might have done wrong..
>
>
> Loren Tedford (KC9ZHV)
> Phone:618-553-0806
> Fax: 1-618-551-2755
> Email: lorentedford at gmail.com
> Email: KC9ZHV at KC9ZHV.com
> http://www.lorentedford.com
> http://www.kc9zhv.com
> http://forum.kc9zhv.com
> http://hub.kc9zhv.com
> http://Ltcraft.net <http://ltcraft.net/>
> http://voipham.com
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/
> mailman/listinfo/app_rpt-users and scroll down to the bottom of the page.
> Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20161105/ab30a20f/attachment.html>


More information about the App_rpt-users mailing list