[App_rpt-users] No PL Tone

REDBUTTON_CTRL jrorke at cogeco.ca
Sun Nov 6 19:22:57 EST 2016


Good catch by Robert.

I think you have to have both carrierfrom and ctcssfrom set to dsp in 
usbradio.conf. for the tone decoding to work.

On 11/6/2016 6:22 PM, Bob Poff wrote:
> Personally I wouldn't bother with using the tone boards in the MII.
>
> On both of mine, I just pulled VOL/SQL HI from the backplane. Then let 
> the usbradio DSP do it all.
>
> On the MIIe (direct FM exciter) I was able to feed both CG and voice 
> into the CG input of the exciter. Measured it to be flat to 8 KC. Then 
> let usbradio do the pre-emphasis, CG encode/decode, and de-emphasis.
>
> On the regular MII (phase modulated exciter), again all DSP. Voice 
> into the exciter mic input, CG encode to the CG input. With the 
> exciter doing the pre-emphasis.
>
> Robert A. Poff
> Loganville, Pa
> ------------------------------------------------------------------------
> *From:* Chris Viningre
> *Sent:* Sun Nov 06 16:19:11 EST 2016
> *To:* Bob Poff
> *Cc:* app_rpt-users at ohnosec.org
> *Subject:* Re: [App_rpt-users] No PL Tone
>
> I may have been unclear on the problem. I can not get the repeater to 
> tone squelch. It is always open. The repeater is working fine other 
> then that. I have tried these settings and still no luck. Thanks for 
> all the help.
>
> Chris
>
>
> On 11/06/2016 10:55 AM, Bob Poff wrote:
>> First of all, you need carrierfrom=dsp not usb.
>>
>> carrierfrom=dsp ; Carrier Detect Source ; Options - 
>> no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - 
>> via USB radio adapter COR connection ; usbinvert - same as above but 
>> inverted polarity. ; dsp - from RX noise using dsp methods ; vox - 
>> voice activated via RX audio
>>
>> Take a look at:
>> https://allstarlink.org/usbradio.html
>>
>> Robert A. Poff
>> Loganville, Pa
>> ------------------------------------------------------------------------
>> *From:* Chris Viningre
>> *Sent:* Sat Nov 05 17:19:25 EDT 2016
>> *To:* app_rpt-users at ohnosec.org
>> *Subject:* [App_rpt-users] No PL Tone
>>
>> I am trying to get the PL tone of 100.0 hz to work on my GE Mastr II
>> repeater. I'm using a URI interface on a laptop running Dail software.
>> Everything is working other than the tones. Here is my rpt.conf and
>> usbradio.conf. Thanks for any help.
>>
>> Chris Viningre
>> 70 W. Roadrunner
>> Salt Flat, Texas 79847
>> C:(915) 504-1510
>> chrisviningre at gmail.com
>> Amateur Radio Operator: WS5B
>> https://www.qrz.com/db/ws5b
>> http://www.reverbnation.com/chrisviningre
>>
>> Radio Repeater configuration file (for use with app_rpt)
>>
>> ;
>>
>>
>>
>> ;
>>
>> ; Your Repeater
>>
>> ;
>>
>>
>>
>> [43934] ; Change this to your assigned node
>> number
>>
>>
>> rxchannel=Radio/usb43934
>>
>> duplex=2
>>
>> erxgain=-3
>>
>> etxgain=3
>>
>> ;controlstates=controlstates
>>
>> scheduler=schedule43934
>>
>> morse=morse43934
>>
>> macro=macro43934
>>
>> functions=functions43934
>>
>> phone_functions=functions43934
>>
>> link_functions=functions43934
>>
>> telemetry=telemetry
>>
>> wait_times=wait-times
>>
>> context = radio
>>
>> callerid = "Repeater"<0000000000>
>>
>> idrecording = |iWS5B
>>
>> accountcode=RADIO
>>
>> hangtime=1000
>>
>>
>>
>> ;
>>
>> ; Usbradio channel driver Configuration
>> File
>>
>> ;
>>
>>
>> [general]
>>
>>
>> [usb43934]
>>
>>
>> hdwtype=0
>>
>> rxboost=1
>>
>> txboost=1
>>
>> rxctcssrelax=1
>>
>> txctcssdefault=100.0
>>
>> rxctcssfreqs=100.0
>>
>> txctcssfreqs=100.0
>>
>> ;rxctcssoverride=0
>>
>> carrierfrom=usb
>>
>> ctcssfrom=usb
>>
>> rxdemod=speaker
>>
>> txprelim=no
>>
>> txlimonly=no
>>
>> txtoctype=no
>>
>> txmixa=composite
>>
>> txmixb=no
>>
>> invertptt=0
>>
>> duplex=1
>>
>> rxondelay=0
>>
>> rxnoisefiltype=0
>>
>> eeprom=0
>> ------------------------------------------------------------------------
>>
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users  and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options
>> button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20161106/588b43cb/attachment.html>


More information about the App_rpt-users mailing list