[App_rpt-users] Problem with Dual Node config with DIAL on RPi3

Steve Zingman szingman at msgstor.com
Sun Apr 23 12:01:09 EDT 2017


Tom,
I'm testing here with the more current version of DIAL for the RPi I am 
testing on a RPi3 with 2 URI
I am trying different configurations to force a failure.

The link is on the allstarlink.org page it is labeled " DIAL RC1 for 
Raspberry Pi 2/3 (Recommended)"
The direct link to the download is 
<http://dvswitch.org/files/DIAL/RAT_RC1.tar.gz>

Thanks, Steve

On 04/23/2017 11:41 AM, Thomas D. Cooney, Jr. wrote:
>
> Steve,
>
> Answers to your three questions:
>
> If I power on the Pi with the second RIM unplugged from USB, the unit 
> boots up and the heart beat on the first RIM is normal.  If I 
> subsequently plug in the second RIM, its heartbeat flashes normally 
> (after about 2 seconds) and the first RIM stays up, both heartbeats 
> are flashing, not quite synchronously, but appear to wig-wag.  Life is 
> good.
>
> If I power up the node with both RIMs connected, the first RIM 
> heartbeat comes on first, much slower than normal, and blinks 
> irregularly for about 3-4 seconds.  Then the second RIM heartbeat 
> starts to flash normally, and the first RIM stops flashing with the 
> heartbeat LED on steady.
>
> (this lsusb report is with both RIMs plugged in, and the Pi powered up 
> – RIM #1 heartbeat on steady, RIM #2 heartbeat flashing normally)
>
> root at 28336:~# lsusb
>
> Bus 001 Device 005: ID 0d8c:013a C-Media Electronics, Inc.
>
> Bus 001 Device 004: ID 0d8c:013a C-Media Electronics, Inc.
>
> Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. 
> SMSC9512/9514 Fast Ethernet Adapter
>
> Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
>
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
> root at 28336:~#
>
> (this lsusb report is with the Pi booted with RIM #1 only, and the 
> second RIM plugged in after boot.  Both RIM heartbeats flashing normally)
>
> root at 28336:~# lsusb
>
> Bus 001 Device 004: ID 0d8c:013a C-Media Electronics, Inc.
>
> Bus 001 Device 005: ID 0d8c:013a C-Media Electronics, Inc.
>
> Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. 
> SMSC9512/9514 Fast Ethernet Adapter
>
> Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
>
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
> root at 28336:~#
>
> (this lsusb report is with the Pi booted with RIM #1 only, the second 
> RIM was left unplugged)
>
> root at 28336:~# lsusb
>
> Bus 001 Device 004: ID 0d8c:013a C-Media Electronics, Inc.
>
> Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. 
> SMSC9512/9514 Fast Ethernet Adapter
>
> Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
>
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
> root at 28336:~#
>
> In all three cases, no other usb devices were connected.  No keyboard, 
> no mouse.  The 3^rd and 4^th USB connectors are empty.
>
> channel driver is usbradio
>
> in rpt.conf, rxchannel = radio/usb for first node, and rxchannel = 
> radio/usb2 for the second node.
>
> ** This does not match the instructions in the allstarlink.org 
> “setting up a two node system” how-to page. **
>
> In usbradio.conf (at the end of [usb] stanzas) I added these lines 
> since I am using the RIM interface pins to control a set of 4 relays.  
> Prior to adding these lines, USB communications would fail because 
> output was not declared.
>
> The second RIM on node 2 has no relay board, so these lines are not 
> present in the [usb2] section of usbradio.conf
>
> gpio5=out1 ; in, out0 or out1
>
> gpio6=out1 ; in, out0 or out1
>
> gpio7=out1 ; in, out0 or out1
>
> gpio8=out1 ; in, out0 or out1
>
> 28336*CLI> core show version
>
> Asterisk 1521 built by root @ repeater on a armv7l running Linux on 
> 2015-10-17 03:09:22 UTC
>
> 28336*CLI>
>
> Rpi2_dial.img was downloaded 11/26/2016 from allstarlink.org portal
>
> Thank you,
>
> *Tom Cooney, Jr., W3SF*
>
> tom at cooneyjr.com
>
> Home: (814)626-1531
>
> Cell: (814)931-0060
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20170423/356a44ea/attachment.html>


More information about the App_rpt-users mailing list