[App_rpt-users] Temporary stop, then restart asterisk

Steve Zingman szingman at msgstor.com
Fri May 26 12:43:47 EDT 2017


As you said, it was when DIAL first released for the RPi so it's 1.0
 From the asterisk CLI:
rpt cmd 1999 cop 2 1999 <------------ system enable
rpt cmd 1999 cop 3 1999 <------------ system disable

replace 1999 with the node number

On 5/26/2017 12:35 PM, Bob wrote:
>
> Actually, just turn the repeater off, then later back on. Will test 
> this. I see I don't have it in rpt.conf.
>
> Also, how do I tell which version of DIAL I have installed?
>
> Thanks,
>
> Bob
>
> ------------------------------------------------------------------------
>
> *From:*App_rpt-users 
> [mailto:app_rpt-users-bounces at lists.allstarlink.org] *On Behalf Of 
> *Bryan D. Boyle
> *Sent:* Friday, May 26, 2017 10:03 AM
> *To:* Users of Asterisk app_rpt
> *Subject:* Re: [App_rpt-users] Temporary stop, then restart asterisk
>
> cop 2 system enable
>
> cop 3 system disable
>
> --
>
> Bryan
>
> Sent from my iPhone 6S...No electrons were harmed in the sending of 
> this message.
>
>
> On May 26, 2017, at 11:57, Mike - W5JR <w5jr.lists at gmail.com 
> <mailto:w5jr.lists at gmail.com>> wrote:
>
>> Do want to stop AllStar/Asterisk or just turn the repeater off? There 
>> is a COP command for the latter. I'm not in front of a terminal to 
>> get you the command.
>>
>> tnx
>> Mike / W5JR
>> Alpharetta GA
>>
>>
>> On May 26, 2017, at 11:46 AM, Bob Pyke <k6ecm1 at gmail.com 
>> <mailto:k6ecm1 at gmail.com>> wrote:
>>
>>> Hmmm... sounds like an update is in order :-)
>>>
>>> Thanks much,
>>>
>>> Bob
>>>
>>> Sent from my iPhone
>>>
>>>> On May 26, 2017, at 8:41 AM, Steve Zingman <szingman at msgstor.com 
>>>> <mailto:szingman at msgstor.com>> wrote:
>>>>
>>>> OK,
>>>>
>>>> /etc/init.d/asterisk stop <--- Stop asterisk
>>>>
>>>> killall -9 asterisk <---------------- Make sure it's dead
>>>>
>>>> ps ax | grep asterisk <--- Check to see if it's really dead
>>>>
>>>> /etc/init.d/asterisk start <--- start asterisk
>>>>
>>>> ps ax | grep asterisk <--- Check to see if it's really started
>>>>
>>>> The newer release candidate fixes this.
>>>>
>>>> 73, Steve N4IRS
>>>>
>>>>> On 5/26/2017 11:37 AM, Bob Pyke wrote:
>>>>>
>>>>> No. It will be off for several minutes, but I want it to stop when 
>>>>> commanded, and start on command. We are conducting an exercise. I 
>>>>> don't know the version, and logging into the node does not say. 
>>>>> We've been operating, pretty much since the introduction of 
>>>>> app_rpt on the RPi
>>>>>
>>>>> Thanks
>>>>>
>>>>> Sent from my iPhone
>>>>>
>>>>>> On May 26, 2017, at 8:31 AM, Steve Zingman <szingman at msgstor.com 
>>>>>> <mailto:szingman at msgstor.com>> wrote:
>>>>>>
>>>>>> Bob,
>>>>>>
>>>>>> Are you talking about "bouncing" asterisk? A stop followed by a 
>>>>>> rapid start? Which distribution and version are you running?
>>>>>>
>>>>>> 73, Steve N4IRS
>>>>>>
>>>>>>> On 5/26/2017 11:28 AM, Bob Pyke wrote:
>>>>>>>
>>>>>>> I have a need to temporarily disable the repeater, then enable 
>>>>>>> it. Timing is critical, so a delay is undesirable. What is the 
>>>>>>> best way to accomplish this? I will be logged into the node.
>>>>>>>
>>>>>>> Thanks,
>>>>>>>
>>>>>>> Bob
>>>>>>>
>>>>>>> Sent from my iPhone
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>>
>>>>>>> App_rpt-users mailing list
>>>>>>>
>>>>>>> App_rpt-users at lists.allstarlink.org 
>>>>>>> <mailto:App_rpt-users at lists.allstarlink.org>
>>>>>>>
>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>>>>
>>>>>>> To unsubscribe from this list please visit 
>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users 
>>>>>>> and scroll down to the bottom of the page. Enter your email 
>>>>>>> address and press the "Unsubscribe or edit options button"
>>>>>>>
>>>>>>> You do not need a password to unsubscribe, you can do it via 
>>>>>>> email confirmation. If y
>>>>>>>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20170526/fc9874d1/attachment-0001.html>


More information about the App_rpt-users mailing list