[App_rpt-users] Icom FR 5000 repeater - URI - Alllstarlink node

REDBUTTON_CTRL jrorke at cogeco.ca
Sun Dec 9 00:24:22 EST 2018


In that case set carrerfrom  = usbinvert
and CTCSSfrom = no

That would use the hard COR from the repeater.

My set doesnt use the hardware cor but uses dsp to decode its own 
squelch from the discriminator.

On 12/8/2018 7:02 PM, Lardizabal David D. wrote:
> Thanks Jon,
>
> Will experiment with your instructions, to see how it works.
>
> Would there be any difference if I use simple usb rather than radio usb?
>
> 73,
>
> David
> HQ2DDL
>
>
>> On Dec 8, 2018, at 16:40, REDBUTTON_CTRL <jrorke at cogeco.ca 
>> <mailto:jrorke at cogeco.ca>> wrote:
>>
>> All connections good except for the red one in question.
>>
>> Change 22  to pin 21 on the FR 5000 and program the I/O pin 21 as an 
>> output. Then assign  function "Analog audible" .
>> set logic to LOW.
>>
>> This will give you an analog COR that is active low when the receiver 
>> is active-should you require it.
>>
>> Program I/O pin 19 to an input and select "EPTT" as its function and 
>> set the logic to LOW.
>>
>> This will make this pin an external ptt.
>>
>> In you uri set up set the following:
>>
>> [usb1999]
>>
>> hdwtype=0
>> rxboost=1
>> txboost=1
>> rxctcssrelax=1
>> txctcssdefault=103.5
>> rxctcssfreqs=103.5
>> txctcssfreqs=103.5
>> ;rxctcssoverride=0
>> carrierfrom=dsp
>> ctcssfrom=dsp
>> rxdemod=flat
>> txprelim=no
>> txlimonly=yes
>> txtoctype=phase
>> txmixa=voice
>> txmixb=no
>> invertptt=0
>> duplex=1
>> rxondelay=0
>> rxnoisefiltype=0
>> eeprom=0
>> plfilter=yes
>>
>> This will set you up using dsp for squelch detection and dsp for rx 
>> tone detection.
>>
>> This setup requires the Icom to be programmed to transmit the ctcss 
>> tone (if desired). the URI will only send Voice to the Icom.
>>
>> Calibrate your RXnoise, RXvoice and RXtone. Then set TX Voice.
>>
>> Save your settings.
>>
>> If your squelch is open type this at the prompt:
>>
>> repeater*CLI> radio tune rxsquelch
>> Current Signal Strength is 681
>> Current Squelch setting is 500
>>
>> if your squelch setting is below your signal strength, set the 
>> squelch to something about 25 points above the current signal strength.
>>
>> repeater*CLI> radio tune rxsquelch 700
>> press enter.
>>
>> Save settings.
>>
>> This set up will require a ctcss tone of 103.5 Hz to access the receive.
>>
>> Also, if you intend to use the allstar node to repeat then set the 
>> channel in the repeater to "duplex" .
>> This is to ensure the allstar node is repeating and not the Icom.
>>
>> Hope this helps.
>>
>> Cheers!
>>
>> Jon VA3RQ
>>
>>
>>
>>
>>
>> On 12/8/2018 5:50 AM, Lardizabal David D. wrote:
>>> Hi
>>>
>>> My name is David Lardizabal HQ2DDL.  I am trying to install and 
>>> AllstarLink node with a repeater Icom FR 5000 and I am trying to 
>>> figure out the pinout / setting on repeater.  If anyone has done 
>>> this setup would appreciate the help.
>>>
>>> I have all ready have done some testing but I am getting a lot of 
>>> noice, like the squelch is open and transmitting to connected node, 
>>> ( I am able to connect to other nodes via line command, I have not 
>>> been able to get the DTMF tones to work to connect/disconnect to nodes.)
>>>
>>> My current pin out is like this:
>>>
>>>
>>> FR 5000 RepeaterDML URI
>>>
>>> 7GND =================> 20GND
>>> 8MOD IN   =================> 22TX AUDIO
>>> 9DISC OUT ================> 21RX AUDIO
>>> 14GND =================> 19GND
>>> 19PTT=================>  1PTT
>>> 22AF OUT  =================>  8COR DET   (?)
>>>
>>> *** as a Note: I found out in a pin out for RTCM with an ICOM FR6000 
>>> repeater;
>>>
>>> I recently connected a Micro-Node RTCM to an ICOM FR6000 UHF repeater.
>>> The FR5000/6000 has a DB25 auxiliary connector on the rear.
>>> Here is the sable pin-out I used. Maybe this helps someone else.
>>>
>>> FR6000                                     RTCM
>>> ----------------------------------------------------------------------
>>> Pin 11 - 12VDC Out ------------------ Pin 1 +V In
>>> Pin 8 - MOD IN ------------------------- Pin 2 TX Audio
>>> Pin 9 Discriminator ------------------- Pin 3 RX Audio
>>> Pin 21 Analog Audible Out -------- Pin 4 CTCSS In
>>> Pin 14 GND------------------------------ Pin 5 GND
>>> Pin 19 EPTT ---------------------------- Pin 7 PTT
>>> DB25 Shell --- soldered to braid---DB9 Shell
>>>
>>> Programming FR6000.
>>> Configured for CTCSS on Receive, no CTCSS on transmit.
>>> Program Pin 21 I/O for Audible Out which is a signal indication when the
>>> receiver is unmuted by squelch/tone.
>>> Program Pin 19 I/O for EPTT - External PTT
>>>
>>> 73
>>>
>>> David
>>>
>>>
>>> _______________________________________________
>>> App_rpt-users mailing list
>>> App_rpt-users at lists.allstarlink.org
>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>
>>> To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users  and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at lists.allstarlink.org 
>> <mailto:App_rpt-users at lists.allstarlink.org>
>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit 
>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users 
>> and scroll down to the bottom of the page. Enter your email address 
>> and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email 
>> confirmation. If you have trouble unsubscribing, please send a 
>> message to the list detailing the problem.
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/app_rpt-users/attachments/20181208/caee5fd5/attachment.html>


More information about the App_rpt-users mailing list